[Free] 2018(Mar) Dumps4cert Testinsides Juniper JN0-360 Dumps with VCE and PDF 161-170

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Mar Juniper Official New Released JN0-360
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/JN0-360.html

Juniper Networks Certified Internet Specialist, – Service Provider (JNCIS-SP)

Question No: 161

You have configured an IP-IP tunnel between Router A and Router B

Which Junos operational mode command is used to verify that the tunnel interface is up and operational?

  1. show chassis tunnel status

  2. show tunnel interface

  3. show interfaces terse

  4. show interfaces tunnel

Answer: C

Question No: 162

– Exhibit –

{master}[edit]

user@router-RE0# run show task replication Stateful Replication: Enabled

RE modE. Master

Protocol Synchronization Status OSPF Complete

RIP Complete BGP Complete MPLS Complete LDP Complete

{master}[edit]

user@router-RE0# run show bgp summary | match 192.168.1.1 192.168.1.1 65056 288 327 0 2 1:05 Establ

{backup}[edit]

user@router-RE1# run show system switchover Graceful switchover: On

Configuration databasE. Ready Kernel databasE. Ready

Peer statE. Steady State

{backup}[edit]

user@router-RE1# run show bgp summary | find 192.168.1.1 192.168.1.1 65056 592 737 3778 2 1:33 Establ

{backup}[edit]

user@router-RE1# run show bgp replication Synchronization master:

Session statE. Up, SincE. 6d 20:42:51

Flaps: 1, Last flap reason: Commit-sync error Protocol statE. Idle, SincE. 5d 19:41:52 Synchronization statE. Complete

Number of peers waitinG. AckWait: 0, SoWait: 0, ScheduleD. 0 rsync walk at: inet.0 – , queued 0

Messages sent: Open 1, Establish 7415, Update 17, Error , Complete 48

Messages receiveD. Open 1, Request 1 wildcard 47 targeted, EstablishAck 2827,

CompleteAck 4

– Exhibit –

Click the Exhibit button.

Referring to the exhibit, which statement is correct?

  1. An RE switchover is likely to result in BGP disruption, but no dataplane impact will be seen.

  2. An RE switchover is likely to result in BGP disruption which will also effect the dataplane.

  3. The system is not yet GRES ready, you need to wait for kernel synchronization to complete.

  4. The system is NSR ready and a switchover should be hitless to the BGP control and data plane.

Answer: D

Question No: 163

You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with the correct prefixes. Which prefix would your ISP likely allocate to your company?

  1. 47-bit prefix

  2. 48-bit prefix

  3. 64-bit prefix

  4. 128-bit prefix

Answer: B

Question No: 164

What are two uses of the AS-path attribute? (Choose two.)

  1. It is used in BGP route selection.

  2. It is used to ensure that a packet traverses the least number of routers.

  3. It is used by IGPs to avoid loops within an autonomous system.

  4. It is used to avoid routing loops between autonomous systems.

Answer: A,D

Question No: 165

Which two statements are true about MPLS VPNs? (Choose two.)

  1. With Layer 3 VPNs, the provider’s routers participate in the customer’s Layer 3 routing.

  2. MPLS VPNs are designed to run over private networks rather than the public Internet.

  3. With Layer 2 VPNs, the provider does not participate in the routing of the customer’s private IP traffic.

  4. MPLS VPN tunnels are always encrypted.

Answer: A,C

Question No: 166

What are three circumstances under which a router sends link-state PDUs (LSPs)? (Choose three)

  1. LSPs are sent periodically every 9 seconds

  2. LSPs are sent when there is a network change

  3. LSPs are sent during adjacency formation

  4. LSPs are sent in response to CSNP messages

  5. LSPs are sent in response to PSNP messages

Answer: B,C,E

Question No: 167

Which two statements are correct regarding VPLS mesh groups? (Choose two.)

  1. Unicast packets destined to another PE router within the same mesh group are dropped by the local PE router.

  2. Unicast packets destined to another PE router in a different mesh group are dropped by the local PE router.

  3. Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded to all local CE routers.

  4. Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded to all remote PE routers.

Answer: A,C

Question No: 168

– Exhibit –

interfaces { ge-0/0/0 { vlan-tagging; unit 100 {

vlan-id 100; family inet {

address 192.168.100.97/30;

}

family iso;

}

unit 200 {

vlan-id 200; family inet {

address 192.168.100.94/30;

}

family iso;

}

}

fxp0 {

description quot;MGMT INTERFACE – DO NOT DELETEquot;;

unit 0 { family inet {

address 10.210.10.11/27;

}

}

}

lo0 { unit 0 {

family inet {

address 192.168.100.1/32;

}

family iso {

address 49.1111.1921.6801.0001.00;

}

}

}

}

protocols { isis {

interface ge-0/0/0.100; interface ge-0/0/0.200;

}

}

– Exhibit –

Click the Exhibit button.

An operator is unable to establish any IS-IS adjacencies on a router in the network. Based on the configuration shown in the exhibit, what is the problem?

  1. Interface lo0 must be configured in the IS-IS hierarchy.

  2. Each network interface needs a unique family ISO address.

  3. The IS-IS level for an each interface must be specified.

  4. The ISO address for interface lo0 is not in hex format.

Answer: A

Question No: 169

Your network consists of multiple remote locations using both IPv4 and IPv6. You have an IPv4-based Internet connection at each site provided by different, local service providers. You are asked to ensure that the remote IPv6 networks are able to communicate.

What should you do?

  1. Create GRE tunnels between the remote locations to connect the IPv6 networks.

  2. Create IPsec tunnels between the remote locations to connect the IPv6 networks.

  3. Create IP-IP tunnels between the remote locations to connect the IPv6 networks.

  4. Create MPLS tunnels between the remote locations to connect the IPv6 networks.

Answer: C

Question No: 170

In an OSPF environment, which two configuration parameters are used to determine which router is the DR? (Choose two.)

  1. the router with the highest priority

  2. the router with the lowest priority

  3. the router with the highest RID

  4. the router with the lowest RID

Answer: A,C

100% Dumps4cert Free Download!
Download Free Demo:JN0-360 Demo PDF
100% Dumps4cert Free Guaranteed!
JN0-360 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.