[Free] 2018(Mar) Dumps4cert Testinsides Juniper JN0-360 Dumps with VCE and PDF 121-130

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Mar Juniper Official New Released JN0-360
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/JN0-360.html

Juniper Networks Certified Internet Specialist, – Service Provider (JNCIS-SP)

Question No: 121

You want to influence how traffic enters your network

Using industry best practices, which two BGP attributes would you modify to accomplish this goal? (Choose two)

  1. AS Path

  2. Local Preference

  3. Next Hop

  4. MED

Answer: A,D

Question No: 122

Which statement correctly describes the difference between a generated and an aggregate route?

  1. An aggregate route can be a supernet whereas generated routes are classful.

  2. A generated route has a forwarding next hop that is inherited from a contributing route.

  3. An aggregate route has a forwarding next hop that is inherited from a contributing route.

  4. Only aggregate routes can be re-advertised through BGP using a policy.

Answer: B

Question No: 123

When sending BGP routes in an Update message, how are they grouped?

  1. by grouping aggregated address ranges together

  2. by using a complete set of matching attributes

  3. by the originating autonomous system

  4. by the originating router

Answer: B

Question No: 124

Click the Exhibit button

Dumps4Cert 2018 PDF and VCE

Based on the illustration shown in the exhibit, what would PE-B do with a VPLS packet received from PE-A if the matching entry in its VPLS routing table showed the destination was connected to PE-D?

  1. PE-B would flood the packet to all attached PEs

  2. PE-B would forward the packet to the root PE device

  3. PE-B would forward the packet to all attached CE devices

  4. PE-B would discard the packet

Answer: C

Question No: 125

For two switches to participate in the same Multiple Spanning Tree Protocol (MSTP) region, which three values must match? (Choose three.)

  1. extended system ID

  2. region name

  3. member VLAN ID list

  4. root bridge ID

  5. revision number

Answer: A,C,E

Question No: 126

What is a reason for an OSPF router to display a designated router ID of 0.0.0.0?

  1. The MTU is mismatched.

  2. The subnet mask is mismatched.

  3. The interface type is point-to-point.

  4. The interface type is broadcast.

Answer: C

Question No: 127

You notice that the RID of your router is being taken from the address of your management interface.

What could cause this scenario?

  1. The loopback address was configured with a /32 address.

  2. The loopback address was not configured under [edit protocols ospf].

  3. A suitable loopback address was not configured on the router.

  4. The loopback address was configured under [edit routing-options].

Answer: C

Question No: 128

– Exhibit – [edit]

user@router# show routing-options rib-groups {

test {

import-rib [ walter.inet.0 nancy.inet.0 ];

}

}

– Exhibit –

Click the Exhibit button.

Referring to the exhibit, what is the result of the RIB group configuration?

  1. All routes from the walter.inet.0 and the nancy.inet.0 routing tables will be imported into the default master routing instance.

  2. Routes from the walter.inet.0 routing table will be imported into the nancy.inet.0 routing table.

  3. All routes will be shared between the walter.inet.0 and the nancy.inet.0 routing tables.

  4. Routes from the nancy.inet.0 routing table will be imported into the walter.inet.0 routing table.

Answer: B

Question No: 129

– Exhibit –

[edit]

user@Router-X# show policy-options policy-statement nhs term 1 {

from { protocol bgp;

neighbor 10.0.21.2;

}

then next-hop self;

}

– Exhibit –

Click the Exhibit button.

Router-X has an external peering session to 10.0.21.2 and several internal peers. How can the policy referenced in the exhibit be used to make sure routes are usable?

  1. Apply nhs as an import policy to internal BGP peers.

  2. Apply nhs as an export policy to internal BGP peers.

  3. Apply nhs as an import policy to external BGP peers.

  4. Apply nhs as an export policy to external BGP peers.

Answer: B

Question No: 130

You are asked to configure a new external BGP connection to a peer#39;s loopback interface. You verify that the peer#39;s loopback interface is reachable, but the BGP connection remains in Idle state.

Which BGP parameter is required to establish the BGP connection?

  1. multipath

  2. multihop

  3. as-override

  4. advertise-inactive

Answer: B

100% Dumps4cert Free Download!
Download Free Demo:JN0-360 Demo PDF
100% Dumps4cert Free Guaranteed!
JN0-360 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.