[Free] 2018(Mar) Dumps4cert Testinsides Juniper JN0-360 Dumps with VCE and PDF 111-120

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Mar Juniper Official New Released JN0-360
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/JN0-360.html

Juniper Networks Certified Internet Specialist, – Service Provider (JNCIS-SP)

Question No: 111

What are three valid BGP message types? (Choose three.)

  1. Refresh

  2. Hello

  3. Route

  4. Keepalive

  5. Open

Answer: A,D,E

Question No: 112

Which three statements correctly describe IBGP and EBGP interaction? (Choose three.)

  1. IBGP is used within an AS, whereas EBGP is used between two different ASs.

  2. EBGP peering is normally loopback-based to provide tolerance for interface or link failures.

  3. By default, EBGP updates the next-hop attribute, whereas IBGP does not.

  4. IBGP speakers can re-advertise IBGP-learned or EBGP-learned routes to other IBGP speakers.

  5. EBGP speakers can re-advertise IBGP-learned or EBGP-learned routes to other EBGP speakers.

Answer: A,C,E

Question No: 113

On an Ethernet segment, OSPF DROther routers from which type of adjacency with each other?

  1. Full

  2. 2Way

  3. ExStart

  4. Exchange

Answer: B

Question No: 114

An established RSVP-signaled LSP suffers a link failure. What is one action taken by the local RSVP-enabled router?

  1. A PathTear message is sent downstream.

  2. A PathErr message is sent upstream.

  3. A PathErr message is sent downstream.

  4. A PathTear message is sent upstream.

Answer: A

Question No: 115

Click the Exhibit button

Dumps4Cert 2018 PDF and VCE

You have two routers connected over a Gigabit Ethernet link as shown in the exhibit It is required that an IS-IS adjacency be established without the need for a designated intermediate system (DIS)

Which configuration statement entered on both routers will achieve this goal?

  1. set interface ge-0/0/2 unit 0 family iso no-dis

  2. set interface ge-0/0/2 unit 0 family iso point-to-point

  3. set protocols isis interface ge-0/0/2.0 no-dis

  4. set protocols isis interface ge-0/0/2.0 point-to-point

Answer: D

Question No: 116

– Exhibit – interfaces { ge-1/0/3 { unit 0 { family inet {

address 192.168.1.1/30;

}

}

}

ge-1/1/0 {

unit 0 { family inet {

address 10.100.10.1/30;

}

}

}

fxp0 { unit 0 {

family inet {

address 10.2.1.13/28;

}

}

}

lo0 { unit 0 {

family inet {

address 10.100.1.1/32; address 127.0.0.1/32;

}

}

}

}

protocols { ospf {

area 0.0.0.0 { interface ge-1/0/3.0;

interface ge-1/1/0.0;

}

}

}

– Exhibit –

Click the Exhibit button.

The router was just powered on.

Referring to the exhibit, what is the OSPF RID?

A. 192.168.1.1

B. 10.100.1.1

C. 127.0.0.1

D. 10.2.1.13

Answer: B

Question No: 117

You have been asked to deploy a Layer 2 VPN for a new customer.

What information will be present in the PE#39;s associated VPN forwarding table? (Choose three.)

  1. the customer site ID

  2. the route distinguisher

  3. the interface encapsulation

  4. the label base

  5. the community name

Answer: A,C,D

Question No: 118

Click the Exhibit button.

Dumps4Cert 2018 PDF and VCE

From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?

  1. The address is not in the aggregate range; the packet is sent to the Routing Engine.

  2. The address is in the aggregate range; the packet will be silently dropped.

  3. The address is not in the aggregate range; the packet will be forwarded.

  4. The address is in the aggregate range; the packet will be dropped.

Answer: A

Question No: 119

Which forwarding table designation is used to indicate that load balancing is working correctly?

  1. ucst

  2. msct

  3. ulst

  4. mlst

Answer: C

Question No: 120

– Exhibit –

Dumps4Cert 2018 PDF and VCE

– Exhibit –

Click the Exhibit button.

You are asked to configure a new external BGP peering. You have configured BGP on R1 as shown in the exhibit, however the BGP peering remains in Active state.

Which additional configuration is required on R1 to establish the BGP peering?

  1. Configure the local-address.

  2. Configure the BGP type as external.

  3. Remove the local-as statement.

  4. Remove the autonomous-system statement.

Answer: C

100% Dumps4cert Free Download!
Download Free Demo:JN0-360 Demo PDF
100% Dumps4cert Free Guaranteed!
JN0-360 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.