[Free] 2018(Mar) Dumps4cert Testinsides Juniper JN0-343 Dumps with VCE and PDF 231-240

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Mar Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 231 – (Topic 3)

Layer 2 interfaces can be assigned to operate in which two modes? (Choose two.)

  1. route

  2. access

  3. trunk

  4. distribution

Answer: B,C

Question No: 232 – (Topic 3)

Which three statements are correct about a Junos firewall filter? (Choose three.)

  1. It examines each packet individually.

  2. It tracks connections and allows you to specify an action to take on all packets within a flow.

  3. It requires you to configure the Junos operating system to explicitly allow traffic in both directions for each connection that you want to permit.

  4. It permits the initial connection and then automatically permits bidirectional communications for this connection.

  5. It is stateless in nature and is used by the software to control traffic passing through the device.

Answer: A,C,E

Question No: 233 – (Topic 3)

With which type of IS-IS router can an IS-IS Level 2-only router form an adjacency?

  1. only other IS-IS Level 2 routers of the same area

  2. any IS-IS router

  3. any other IS-IS Level 2 router

  4. IS-IS Level 1 routers of the same area

Answer: C

Question No: 234 – (Topic 3)

You have created an IP-IP tunnel which will traverse interface at-0/1/0 and you would like to make sure that the tunnel is operational. Which operational-mode command should you use to verify that the IP-IP tunnel interface is up?

  1. show ip tunnels interfaces

  2. show interfaces at-0/1/0 terse

  3. show interfaces ip-0/0/0 terse

  4. show ip-0/0/0 interfaces terse

Answer: C

Question No: 235 – (Topic 3)

Which statement describes an OSPF area for which no-summaries is configured?

  1. The ABR does not generate any Summary (Type 3) LSAs towards the backbone.

  2. The ABR does not generate any Summary (Type 3) LSAs for other OSPF areas.

  3. The area does not summarize external routes generated within its area.

  4. The area does not accept or create summaries of any kind.

Answer: B

Question No: 236 – (Topic 3)

You want to ensure that all traffic arriving on interface fe-0/0/0.0 will be routed to next-hop, regardless of the more specific routes that might appear in the routing table. How can you accomplish this configuration?

  1. Configure a default route with a next hop of and configure the always-use flag for the route.

  2. Configure and apply a firewall filter that sends all traffic to a routing instance, configure a default route in that routing instance, and configure the router to install interface routes in that routing instance.

  3. Configure a routing policy that matches all traffic and sets the next hop to, and configure a RIB group to ensure that the routing policy can resolve the next hop to

  4. Configure a firewall filter that matches all traffic and sets the next hop to, apply the firewall filter to a RIB group, and assign the fe-0/0/0.0 interface to that RIB group.

Answer: B

Question No: 237 – (Topic 3)

What describes the action of the qualified-next-hop parameter in a configuration?

  1. It performs a recursive lookup on the destination network to confirm that the route is reachable.

  2. It allows for the configuration of independent preferences for static routes to the same destination.

  3. It periodically pings the next hop to validate its existence thereby assigning the static route to the forwarding table.

  4. It verifies the maximum hop count limit before validating the static route.

Answer: B

Question No: 238 – (Topic 3)

Dumps4Cert 2018 PDF and VCE

You configure a network according to the topology shown in the exhibit but find that users attached to R7 are having difficulty communicating with the rest of the network. What are two solutions to the problem? (Choose two.)

  1. Configure Area as a stub area.

  2. Create a virtual link between R3 and R6.

  3. Configure an OSPF export policy on R6 to export routes from Area to Area and from Area to Area

  4. Connect R6 to Area

Answer: B,D

Question No: 239 – (Topic 3)

Dumps4Cert 2018 PDF and VCE

Router-A and Router-B shown in the exhibit are peering between their loopback interfaces. Which operational command on Router-A do you use to display all the BGP routes received from Router-B?

  1. show route receive-protocol bgp all

  2. show route receive-protocol bgp all

  3. show bgp rib-in neighbor

  4. show bgp receive-protocol bgp

Answer: A

Question No: 240 – (Topic 3)

Dumps4Cert 2018 PDF and VCE

Router 2 is receiving two announcements of a route to Router 2 learned one version of the route from ISP-2; this announcement of the route was received first. The second announcement of the route was received from Router 1 using IBGP. What will Router 2 do with the routes shown in the exhibit?

  1. Router 2 will choose to forward traffic toward ISP 2 because this route was learned first.

  2. Router 2 will choose to forward traffic toward Router 1 because newer routes are preferable.

  3. Router 2 will choose to forward traffic toward ISP 2 because EBGP-learned routes are preferred over IBGP-learned routes.

  4. Router 2 will choose to forward traffic toward Router 1 because IBGP-learned routes are preferred over EBGP-learned routes.

Answer: C

100% Dumps4cert Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Dumps4cert Free Guaranteed!
JN0-343 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.