[Free] 2018(Mar) Dumps4cert Testinsides Juniper JN0-343 Dumps with VCE and PDF 221-230

Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 Mar Juniper Official New Released JN0-343
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/JN0-343.html

Juniper Networks Certified Internet Specialist (JNCIS-ENT)

Question No: 221 – (Topic 3)

What is a difference between a generated route and an aggregated route?

  1. Generated routes have a higher preference by default.

  2. Generated routes use a next hop of discard.

  3. Generated routes have a lower preference by default.

  4. Generated routes use a next hop of a contributing route.

Answer: D

Question No: 222 – (Topic 3)

Which three statements are correct about an AE interface? (Choose three.)

  1. It can be configured as either active or passive.

  2. It always load balances traffic equally.

  3. It can support LACP.

  4. It is referred to as a LAG.

  5. It can be configured as active only.

Answer: A,C,D

Question No: 223 – (Topic 3)

For two OSPF neighbors to establish a full adjacency on a broadcast medium, what information in their hello packets must match? (Choose two.)

41 / 79

  1. network mask

  2. router priority

  3. dead interval

  4. the list of neighbors on the network

Answer: A,C

Question No: 224 – (Topic 3)

Dumps4Cert 2018 PDF and VCE

Router-A and Router-B shown in the exhibit are peering between their loopback interfaces. Which operational-mode command on Router-B do you use to display the BGP routes advertised to Router-A?

  1. show route advertising-protocol bgp 10.10.10.2

  2. show route advertising-protocol bgp 10.10.10.1

  3. show bgp rib-out neighbor 10.10.10.1

  4. show bgp neighbor 10.10.10.1 advertised-routes

Answer: B

Question No: 225 – (Topic 3)

Dumps4Cert 2018 PDF and VCE

In the exhibit, Area 2.2.2.2 is configured as a not-so-stubby area and Area 1.1.1.1 is configured as a normal area. R5 has an export policy that causes the RIP network prefixes to be announced through OSPF. Which LSA type does R7 receive describing the RIP network prefixes?

  1. Summary (Type 3)

  2. ASBRSum (Type 4)

  3. Extern (Type 5)

  4. NSSA (Type 7)

Answer: C

Question No: 226 – (Topic 3)

ON NO: 207

What is preserved by enabling graceful Routing Engine switchover (GRES)?

  1. control-plane state

  2. link-state protocol adjacencies

  3. interface and kernel information

  4. BGP peering relationships

Answer: C

Question No: 227 – (Topic 3)

You want to configure a redundant trunk group on a switch. You want ge-0/0/0.0 to be the default link; however, if ge-0/0/0.0 fails and the switch begins using ge-0/0/1.0, you want the switch to continue using ge-0/0/1.0 until ge-0/0/1.0 fails. Which configuration will accomplish this scenario?

  1. redundant-trunk-group { interface ge-0/0/0.0 { primary;

    }

    interface ge-0/0/1.0 { primary;

    }

    }

  2. redundant-trunk-group { interface ge-0/0/0.0; interface ge-0/0/1.0;

    no-preempt;

    }

  3. redundant-trunk-group { interface ge-0/0/0.0 { primary;

    }

    interface ge-0/0/1.0;

    }

  4. redundant-trunk-group { interface ge-0/0/0.0; interface ge-0/0/1.0;

}

Answer: D

Question No: 228 – (Topic 3)

You review the current LSA database and you suspect that your LSA database contains

stale or invalid database entries. You need to verify that your router is receiving LSAs from other routers in your network.

Which action would you take to correct this problem?

  1. Purge the LSDB.

  2. Increase the max-age attribute for the LSDB.

  3. Decrease the max-age attribute for the LSDB.

  4. Disable and enable the interfaces.

Answer: A

Question No: 229 – (Topic 3)

Which configuration allows the virtual IP address to respond to pings?

  1. [edit interfaces fe-0/0/0 unit 50 family inet address 192.168.0.12/24] user@RouterA# show

    vrrp-group 50 {

    virtual-address 192.168.0.1;

    fast-interval 250; preempt;

    accept-data;

    }

  2. [edit interfaces fe-0/0/0 unit 50 family inet address 192.168.0.12/24] user@RouterA# show

    vrrp-group 50 {

    virtual-address 192.168.0.1;

    fast-interval 250; no-preempt;

    no-accept-data;

    }

  3. [edit interfaces fe-0/0/0 unit 50 family inet address 192.168.0.12/24] user@RouterA# show

    vrrp-group 50 {

    virtual-address 192.168.0.1;

    fast-interval 250; accept-icmp;

    }

  4. [edit interfaces fe-0/0/0 unit 50 family inet address 192.168.0.12/24] user@RouterA# show

vrrp-group 50 {

virtual-address 192.168.0.1;

priority 220;

advertise-interval 10; preempt;

accept-packets;

}

Answer: A

Question No: 230 – (Topic 3)

Which configuration will cause IPv4 interface routes from inet.0 to appear in the myinstance routing instance?

  1. routing-options { interface-routes {

    rib-group inet myribgroup;

    }

    rib-groups { myribgroup {

    import-rib [ inet.0 myinstance.inet.0 ];

    }

    }

    }

  2. routing-options { interface-routes {

    rib-group inet myribgroup;

    }

    rib-groups { myribgroup { export-rib inet.0;

    import-rib myinstance.inet.0;

    }

    }

    }

  3. routing-options { interface-routes {

    import into myinstance.inet.0;

    }

    }

  4. routing-options { rib-groups { interface-routes {

import-rib [ inet.0 myinstance.inet.0 ];

}

}

}

Answer: A

100% Dumps4cert Free Download!
Download Free Demo:JN0-343 Demo PDF
100% Dumps4cert Free Guaranteed!
JN0-343 Dumps

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.