[Free] 2018(Aug) Ensurepass Cisco 200-355 Dumps with VCE and PDF 211-220

Ensurepass.com : Ensure you pass the IT Exams
2018 Aug Cisco Official New Released 200-355
100% Free Download! 100% Pass Guaranteed!

Implementing Cisco Wireless Network Fundamentals

Question No: 211

An engineer wants to set up guest wireless that requires users to log in via a splash page prior to accessing the network. Which authentication method should be configured?

  1. LDAP


  3. local authentication

  4. WebAuth

  5. PSK

Answer: D

Question No: 212 DRAG DROP

Drag the propagation behavior on the left to the corresponding environment on the right.

Ensurepass 2018 PDF and VCE


Ensurepass 2018 PDF and VCE

Question No: 213

Which interface is considered a dynamic interface?

  1. the virtual interface

  2. the AP manager interface

  3. the LAG interface

  4. the management interface

  5. the service port interface

  6. a WLAN client data interface

Answer: F

Question No: 214

An engineer wants to deploy a 2504 controller as the anchor controller for a guest WLAN that resides on a 5508 controller in a different mobility group. What configuration change must be applied to support this deployment strategy?

  1. UDP 16666 and IP Protocol 97 must be enabled on the 2504 controller

  2. UDP 5246 and TCP Protocol 97 must be enabled on the router

  3. The 2504 controller must be added to the same mobility group as the 5508.

  4. DHCP Option 43 must be added to the neighboring switchport

Answer: C

Question No: 215

What is the function of the Cisco AnyConnect DART tool?

  1. creates a compressed bundle of client logs and information

  2. visualizes a WLAN environment, showing the possible locations of problems

  3. gathers statistics from neighboring clients for comparison to the baseline

  4. helps to troubleshoot a WLAN connection by using easy-to-use wizards and statistic viewers

Answer: A

Question No: 216

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

In setting up the wireless network, it is desired that the DHCP server that is configured in WLC1 provides IP addressing to the WLAN. When devices attempt to join the network, they fail to receive an IP address in the range provided by the DHCP server in WLC1, but they do receive an IP address from the DHCP server in SW1. What is causing this issue?

  1. The external DHCP server in SW1 will always be the preferred DHCP server and WLC1 will always be the secondary DHCP server in the WLAN.

  2. The DHCP server address for SW1 needs to be removed from the DHCP server configuration in WLC1.

  3. The primary DHCP server address in WLC1 is incorrect.

  4. The primary DHCP server configured in WLC1 is not enabled.

Answer: D

Question No: 217

An engineer has been noticing the power settings on several of the office APs change from day to day ever since two more APs were installed. After logging into the WLC, the engineer verifies that the power levels on 4 of the 802.11n radios are fluctuating up and down. What is the reason for this?

  1. The controller has the APs in H-REAP mode and are on a Layer 2 connection instead of Layer 3.

  2. The RRM has revealed a bad survey and is attempting to power down some of the radios to make up for it.

  3. The WLC has created temporary coverage holes while stepping through power levels for some of the APs.

  4. Several APs have high levels of overlapping coverage in the same area and the WLC is using RRM to correct the cell sizes AP coverage.

Answer: D

Question No: 218

Refer to the exhibit.

Ensurepass 2018 PDF and VCE

Which tool is shown?

  1. Cisco WCS client troubleshooting tool

  2. Cisco WLC client troubleshooting tool

  3. WLAN Client Debug Analyzer

  4. Cisco WLAN Connection Advisor

Answer: A

Question No: 219

When calculating the link budget for a wireless point-to-point bridge, the engineer notices that one antenna has its gain marked as 2.85 dBd. With a 20-mW access point and 3-dBi loss for the cable, what is the approximate EIRP?

  1. 15 dBm

  2. 18 dBm

  3. 22 dBm

  4. 25 dBm

Answer: A

Question No: 220

Which two algorithms are available in RRM? (Choose two.)

  1. coverage-hole detection

  2. dynamic channel assignment

  3. RSSI normalizer

  4. transmitting channel expander

  5. rogue detection

Answer: A,B

100% Ensurepass Free Download!
200-355 PDF
100% Ensurepass Free Guaranteed!
200-355 Dumps

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.