Download New Updated (Spring 2015) Microsoft 74-697 Actual Tests 51-60

Ensurepass

 

QUESTION 51

You plan to deploy operating systems to several servers. The servers have RAID controllers.

 

You plan to install three hard disks on each server.

 

You need to configure the servers to meet the following requirements:

 

clip_image002Ensure that all data will be available if a single disk fails.

clip_image002[1]Provide the highest amount of disk space to store files.

 

Which RAID level should you configure on the servers?

 

A.

RAID 0

B.

RAID 1

C.

RAID 5

D.

RAID 6

 

Correct Answer: C

Explanation:

RAID 5 works with three or more disks, and protects against failure of one disk.

 

 

QUESTION 52

You have several reference computers. The computers are configured to always start from a local hard disk drive. You plan to capture the reference computers. On each reference computer, you connect a USB flash drive (UFD) that contains an installation of Windows Preinstallation Environment (Windows PE). You need to ensure that the reference computers start automatically by using Windows PE from the UFD. What should you do?

 

A.

From the System Configuration utility, modify the Boot settings.

B.

Run bdcedit.exe and modify the boot configuration data (BCD) store.

C.

From the BIOS options, modify the startup order.

D.

From the System Properties, modify the Startup and Recovery settings.

 

Correct Answer: C

Explanation:

Change the boot order in BIOS.

 

 

QUESTION 53

You plan to deliver 100 client computers to a customer. The computers will run Windows 8. All of the computers support only Unified Extensible Firmware Interface (UEFI) Class 2. You need to enable Secure Boot for the computers. Which UEFI settings on the computers should you modify?

 

A.

Disable support for the compatibility support module (CSM).

B.

Enable support for the Trusted Platform Module (TPM).

C.

Enable support for the compatibility support module (CSM).

D.

Disable support for the Trusted Platform Module (TPM).

 

Correct Answer: A

Explanation:

Secure Boot is supported for UEFI Class 2 and Class 3 PCs. For UEFI Class 2 PCs, when Secure Boot is enabled, the compatibility support module (CSM) must be disabled so that the PC can only boot authorized, UEFI-based operating systems.

 

 

QUESTION 54

You work for an OEM system builder named Fabrikam, Inc. You use Windows Deployment Services (WDS) to start bare metal deployments that use Pre-Boot Execution Environment (PXE) and a 32-bit boot image. The boot image starts to a command prompt and automatically establishes a network connection. You plan to create a reference image of the 64-bit version of Windows 8 Pro. From the distribution share, you execute Windows Setup from the Windows 8 Pro 64-bit source files and you receive an error message indicating that Windows Setup is incompatible with the version of Windows that you are running. You need to ensure that you can create the reference image. What should you do?

 

A.

Configure the BIOS to use Unified Extensible Firmware Interface (UEFI) mode.

B.

Run setup.exe and specify the /InstallFrom parameter.

C.

Create a boot image that contains a 64-bit version of Windows Preinstallation Environment (Windows PE).

D.

Specify the MetaData setting in an answer file.

 

Correct Answer: C

Explanation:

To install a 64-bit version of Windows you must use a 64-bit version of Windows PE. Likewise, to install a 32-bit version of Windows, you must use a 32-bit version of Windows PE.

 

 

QUESTION 55

You have three images sealed in Out-of-Box-Experience (OOBE) mode. You use the images on a daily basis to build client computers for customers. A new customer places an order for 500 computers. The customer’s requirements for the computers are not met by any of the images. You identify an image that you can modify by installing two applications required by the cutomer. You plan to customize the image before you deploy the image to the computers. You need to identify which steps must be taken to modify the image. What should you do before you capture the image?

 

A.

Start the image in audit mode on a reference computer. Install the required applications. Seal the image in audit mode.

B.

Start the image in audit mode on a reference computer. Install the required applications. Seal the image in OOBE mode.

C.

Start the image in audit mode on a reference computer. Install the required applications. Restart the computer.

D.

Start the image on a reference computer. Install the required applications. Seal the image in audit mode.

 

Correct Answer: B

 

 

QUESTION 56

You plan to deploy multiple client computers that will each contain a 4-TB hard disk drive. The hard disk drives will be initialized as GPT drives. You need to identify the maximum number of primary partitions that can be created on a GPT drive. How many primary partitions should you identify?

 

A.

4

B.

64

C.

128

D.

256

 

Correct Answer: C

Explanation:

A GPT disk uses the GUID partition table (GPT) disk partitioning system. A GPT disk offers these benefits:

Allows up to 128 primary partitions. Master Boot Record (MBR) disks can support up to four primary partitions and an additional 124 partitions inside extended partitions.

 

 

QUESTION 57

You have the Windows Assessment and Deployment Kit (Windows ADK) installed. You create a Windows Preinstallation Environment (Windows PE) image. While testing the deployment of the Windows PE image, you discover that the Windows PE installation becomes unresponsive. You discover that you are exceeding the memory capacity of the RAM disk. You need to increase the memory capacity of the RAM disk used by the Windows PE image. You mount the Windows PE image. Which command should you run next?

 

A.

dism /cleanup-wim

B.

dism /image:c:imageswpe /set-scratchspace:256

C.

dism /image:c:imageswpe /scratchdir:c:imageswpe

D.

dism /online /set-scratchspace:256

 

Correct Answer: B

Explanation:

* /Image:<path_to_offline_image_directory> This is the full path to the root directory of the offline Windows image that you will service.

* /Set-ScratchSpace:

Sets the available scratch space, in megabytes. Valid values are 32, 64, 128, 256 and 512.

Example:

Dism /image:C:testoffline /set-ScratchSpace:128

 

 

QUESTION 58

You have a server named Server1 that runs Windows Server 2012 and has the Windows Deployment Services server role installed. You recently removed a third-party DHCP server from the network, and then installed the DHCP Server server role on Server1. You create a scope on Server1. You discover that client computers attempting to receive a Windows 8 image fail to connect to Server1. You verify that the client computers on the network can receive an IP address from Server1. You need to ensure that the computers attempting to receive an image can connect to Server1. Which two actions should you perform? (Each correct answer presents part of the solution. Choose two.)

 

A.

From the DHCP console, click Server Options, and then set the value of Option 66 to Server1.

B.

From the Windows Deployment Services console, click the PXE Response tab, and then set the value of the Delay in seconds to 3.

C.

From the Windows Deployment Services console, click the DHCP tab, and then select the Do not listen on port 67 check box.

D.

From the DHCP console, click Server Options, and then set the value of Option 67 to install.wim.

E.

From the Windows Deployment Services console, click the DHCP tab, and then select the Configure DHCP option 60 to indicate that this is also a PXE server check box.

 

Correct Answer: CE

Explanation:

If DHCP and WDS roles are installed on same server?

In this case you must tell WDS not to listen on port 67 and set DHCP option 60 so that clients can find the WDS server. So options Do not listen on port 67 (C) and Configure DHCP option 60 to indicate that this server is also a PXE server (E) must be checked.

 

clip_image003

 

Reference:

Deploying Windows 7 Using Windows Deployment Services

 

 

QUESTION 59

A customer plans to deploy Windows Server 2012 Standard to several servers.

 

The customer identifies the following hardware requirements for the planned deployment:

 

clip_image002[2]Must support three volumes in a single mirror without the installation of third-party management software.

clip_image002[3]Must support NIC teaming without the installation of third-party management software.

clip_image002[4]Must be able to back up the server data to a tape device.

clip_image002[5]Must be able to run on an x86 hardware platform.

 

You need to identify which two requirements are met by the planned deployment of Windows Server 2012.

Which two requirements should you identify? (Each correct answer presents part of the solution. Choose two.)

 

A.

Must support three-way mirrors without the installation of third-party management software.

B.

Must support NIC teaming without the installation of third-party management software.

C.

Must be able to run on an x86 hardware platform.

D.

Must be able to back up the server data to a tape device.

 

Correct Answer: AB

Explanation:

Three-way mirroring are available in Windows Server 2012 through Storage Space. The new NIC Teaming capability in the Windows Server 2012 bring continuous network availability and increased network performance, supporting greater VM density and lower operational costs.

 

Incorrect:

Not C: Windows Server 2012 runs only on x64 processors. Unlike its predecessor, Windows Server 2012 does not support Itanium.

 

Note:

x86-64 (also known as x64, x86_64 and amd64) is the 64-bit version of the x86 instruction set. It supports vastly larger amounts of virtual memoryand physical memory than is possible on its predecessors, allowing programs to store larger amounts of data in memory. x86-64 also provides 64-bitgeneral purpose registers and numerous other enhancements.

 

Not D:

* Windows Backup has not supported backing up to tape for quite sometime now.You’ll need something like Microsoft’s Data Protection Manager or a 3rdparty solution.

* You can no longer back up to tape.

Windows Server Backup supports backing up to external and internal disks, DVDs, and shared folders.

 

 

QUESTION 60

You have a Windows Recovery Environment (Windows RE) image named Winre.wim. You need to enable support for HTML applications in the image. Which tool should you use?

 

A.

Winrecfg

B.

Reagentc

C.

Sysprep

D.

Dtsm

 

Correct Answer: A

Explanation:

WinPE-WinReCfg contains the Winrecfg.exe tool, and it enables the following scenarios:

Boot from x86-based Windows PE to configure Windows RE settings on an offline x64- based operating system image.

Boot from x64-based Windows PE to configure Windows RE settings on an offline x86- based operating system image.

 

Incorrect:

Not B: Reagentc

Configures the Windows Recovery Environment (Windows RE) and enables image recovery solutions.

Free VCE & PDF File for Microsoft 74-697 Real Exam

Instant Access to Free VCE Files: MCSE|MCSA|MCITP…
Instant Access to Free PDF Files: MCSE|MCSA|MCITP…